[Oct 16, 2021] Get Free Updates Up to 365 days On Developing NACE-CIP1-001 Braindumps
Best Quality NACE NACE-CIP1-001 Exam Questions
NEW QUESTION 46
Prior to using Inspection Tools the inspector must:
- A. a), b) & c)
- B. Be trained on how to use the instrument
- C. Ensure the instrument is within calibration parameters
- D. Read the manufactures' instructions
Answer: A
NEW QUESTION 47
Checking is
- A. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- B. a fine crack in the surface of a coating that rarely reaches the substrate
- C. an exposed area of the substrate or previous coat material, caused by poor application technique.
- D. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
Answer: B
NEW QUESTION 48
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. alligatoring.
- B. checking.
- C. cracking.
- D. blistering.
Answer: B
NEW QUESTION 49
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Never change his/her mind
- B. Call the supervisor
- C. Go with the majority opinion
- D. Achieve consensus through negotiation
Answer: B
NEW QUESTION 50
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Power tools
- B. Airless spray equipment
- C. Abrasive blast nozzles
- D. Hand tools
Answer: A
NEW QUESTION 51
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. how the item was coated.
- B. when the coating will be reapplied.
- C. what materials were used.
- D. what items were coated.
Answer: A
NEW QUESTION 52
A NACE Coating Inspector is permitted to transport coating material when:
- A. Asked to do so by the Owner's Representative
- B. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- C. Asked to do so by the Coating Application team
- D. The Inspector should never transport coating material
Answer: D
NEW QUESTION 53
Stripe coats are generally applied to:
- A. Welds
- B. Complex geometric shapes
- C. a), b), and c)
- D. Edges and corners
Answer: C
NEW QUESTION 54
Non Conformance Reports are completed by the Inspector:
- A. In accordance with the specification's definition of a non-conformance
- B. In every instance that an item does not meet the specification requirements
- C. When the Inspector deems it to be a significant non-conforming item
- D. When the Inspector and Contractor deem it to be a significant non-conforming item
Answer: D
NEW QUESTION 55
An Inspector should change position when:
- A. The Owner can save some money by the change
- B. The Inspectors position is not the majority position
- C. The Inspector is convinced by verifiable facts
- D. Only when directed by the supervisor
Answer: C
NEW QUESTION 56
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. Pass/fail criteria
- B. A final conflict resolution method
- C. A method to grade surface profile
- D. A general guide
Answer: D
NEW QUESTION 57
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. white metal blast cleaning.
- B. near-white metal blast cleaning.
- C. commercial blast cleaning.
- D. brush-off blast cleaning.
Answer: D
NEW QUESTION 58
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- B. Document the problem and advise the Contractor and Owner's representative
- C. Break the blisters to see what's inside
- D. Document the problem and advise the Contractor
Answer: B
NEW QUESTION 59
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Call the coating manufacturer for clarification
- B. Call the person who wrote the specification for clarification
- C. Use the product data sheet as a guide
- D. Use the job specification as a guide
Answer: D
NEW QUESTION 60
Removal of surface contaminants is done by:
- A. Scarifying
- B. Waterjetting
- C. A combination of methods
- D. Abrasive blasting
Answer: C
NEW QUESTION 61
......
NACE Exam Practice Test To Gain Brilliante Result: https://www.ipassleader.com/NACE/NACE-CIP1-001-practice-exam-dumps.html
Tested Material Used To NACE-CIP1-001: https://drive.google.com/open?id=1YPp7vgAFEByzqG3jY6D6R9ZSC8eIdQRq