[Nov 06, 2021] Get Free Updates Up to 365 days On Developing NACE-CIP1-001 Braindumps
Best Quality NACE NACE-CIP1-001 Exam Questions
NEW QUESTION 19
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. Low Surface Temperature
- B. High Relative Humidity
- C. Low Relative Humidity
- D. High Surface Temperature
Answer: C
NEW QUESTION 20
The main responsibilities of the inspector are to
- A. demonstrate to the contractor how to apply the coating.
- B. observe and report the quality of the work performed.
- C. direct and perform the work stated in the specification.
- D. observe and direct the work of the contractors.
Answer: B
NEW QUESTION 21
The most important factor resulting in improved job site safety is:
- A. Situational Awareness
- B. Personal Protective Equipment
- C. Safety Enforcement
- D. Engineering Controls
Answer: A
NEW QUESTION 22
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. cracking.
- B. sagging.
- C. checking.
- D. holiday.
Answer: D
NEW QUESTION 23
NACE SP 0178 is a standard for:
- A. Structural steel to be coated for Atmospheric Service
- B. Tanks and Vessels to be Externally Coated
- C. Tanks and Vessels to, be Lined for Immersion Service
- D. Stainless steel pipe to be Externally Coated
Answer: C
NEW QUESTION 24
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which power tool the Contractor selects
- B. It depends on which hand tool the Contractor selects
- C. Yes, because the 'two standards are not equivalent
- D. No, because there is no real difference in the standards
Answer: D
NEW QUESTION 25
Solvents are added to coating formulations to
- A. increase film permeability.
- B. dissolve binders and form liquid coatings.
- C. decrease film permeability.
- D. provide color.
Answer: B
NEW QUESTION 26
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Taking measurements too far from the edge of a surface
- B. Rotating the dial too fast when taking measurements
- C. Measuring ditty, tacky, or soft films
- D. Failing to determine the base metal reading (BMR)
Answer: B,C,D
NEW QUESTION 27
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. brush-off blast cleaning.
- B. commercial blast cleaning.
- C. near-white metal blast cleaning.
- D. white metal blast cleaning.
Answer: A
NEW QUESTION 28
If inspectors identify issues of non-conformance during an inspection, they should
- A. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- B. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- C. perform additional tests secretly to ensure there are no other potential issues at the site
- D. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
Answer: D
NEW QUESTION 29
If a Thermoset coating is heated it will:
- A. Harden and return to its original hardness when cooled
- B. Harden and retain its hardness when cooled
- C. Soften when heated and retain its softness when cooled
- D. Soften when heated and return to its original hardness when cooled
Answer: B
NEW QUESTION 30
Non Conformance Reports are completed by the Inspector:
- A. In every instance that an item does not meet the specification requirements
- B. In accordance with the specification's definition of a non-conformance
- C. When the Inspector and Contractor deem it to be a significant non-conforming item
- D. When the Inspector deems it to be a significant non-conforming item
Answer: C
NEW QUESTION 31
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 2.5 millimeters (.10 inch)
- B. 1 cm (.39 inch)
- C. 6.35 cm (2.5 inch)
- D. 2.5 cm (1 inch)
Answer: D
NEW QUESTION 32
Galvanic corrosion occurs on which of the following substrates:
- A. Metal
- B. Concrete
- C. Fiberglass Reinforced Plastic
- D. Wood
Answer: A
NEW QUESTION 33
Owners hire NACE Inspectors' with the expectation that:
- A. a) and c)
- B. The Inspector will improve job flow and schedule
- C. The Inspector will make a meaningful technical contribution to the job
- D. The inspection cost will be offset by an improvement in service life
Answer: A
NEW QUESTION 34
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. Only if the specification requires it
- B. In the office only
- C. At all times
- D. In the field only
Answer: C
NEW QUESTION 35
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- D. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
Answer: B
NEW QUESTION 36
Corrosion generally occurs at which of the following sites:
- A. Electrolyte
- B. Cathode
- C. Metallic pathway
- D. Anode
Answer: D
NEW QUESTION 37
Which of these tests uses a syringe?
- A. Potassium ferricyanide
- B. Sleeve test
- C. Soluble salts meter
- D. Bresle patch
Answer: D
NEW QUESTION 38
Which one of these elements is not necessary for corrosion to occur:
- A. Electrolyte
- B. Anode
- C. Cathode
- D. Reference Cell
Answer: D
NEW QUESTION 39
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION 40
Prior to using Inspection Tools the inspector must:
- A. a), b) & c)
- B. Read the manufactures' instructions
- C. Be trained on how to use the instrument
- D. Ensure the instrument is within calibration parameters
Answer: A
NEW QUESTION 41
......
NACE Exam Practice Test To Gain Brilliante Result: https://www.ipassleader.com/NACE/NACE-CIP1-001-practice-exam-dumps.html
Tested Material Used To NACE-CIP1-001: https://drive.google.com/open?id=1nkOvEYvj1fYZ8TyUC60A_lYMjxKrbphF