NACE-CIP1-001 Practice Exam and Study Guides - Verified By iPassleader Updated 100 Questions
2025 Updated Verified Pass NACE-CIP1-001 Study Guides & Best Courses
You can find out about the exam cost of NACE CIP1-001 Certification.
The NACE CIP1-001 certification exam is affordable. It costs about $300.
NEW QUESTION # 25
Which one of these elements is not necessary for corrosion to occur:
- A. Reference Cell
- B. Electrolyte
- C. Cathode
- D. Anode
Answer: A
NEW QUESTION # 26
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. develops a good anchor profile resulting in uneven coating application.
- B. damages structural elements thereby speeding up the corrosion process.
- C. scratches the surface too deeply resulting in uneven coating application
- D. develops a polished surface, which is a poor anchor profile for most coatings
Answer: D
NEW QUESTION # 27
SSPC SP 1 identifies the use of:
- A. Organic solvents
- B. Inorganic solvents
- C. Biodegradable detergents
- D. A wide variety of materials
Answer: D
NEW QUESTION # 28
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 45 Gauge readings resulting in 15 Spot Measurements
- B. 105 Gauge Readings resulting in 35 Spot Measurements
- C. 75 Gauge Readings resulting in 25 Spot Measurements
- D. 225 Gauge Readings resulting in 75 Spot Measurements
Answer: D
NEW QUESTION # 29
Passivation can best be described as:
- A. Complete elimination pf the corrosion process
- B. A protective metallic oxide surface layer that slows corrosion
- C. A coating layer applied to the surface to inhibit corrosion
- D. Treating metal with a liquid inhibiter
Answer: B
NEW QUESTION # 30
Conventional spray is a good choice when:
- A. High production rates are required
- B. High quality finishes are required
- C. High transfer efficiency is required
- D. High viscosity coatings are being applied
Answer: B
NEW QUESTION # 31
The main responsibilities of the inspector are to
- A. observe and direct the work of the contractors.
- B. direct and perform the work stated in the specification.
- C. observe and report the quality of the work performed.
- D. demonstrate to the contractor how to apply the coating.
Answer: C
NEW QUESTION # 32
NACE Level 1 Inspectors have been trained to perform:
- A. All types of inspection
- B. Visual inspection, Non-Destructive and Destructive testing
- C. Visual inspection and Non-destructive testing
- D. Visual inspection only
Answer: C
NEW QUESTION # 33
Non Conformance Reports are completed by the Inspector:
- A. In accordance with the specification's definition of a non-conformance
- B. When the Inspector deems it to be a significant non-conforming item
- C. In every instance that an item does not meet the specification requirements
- D. When the Inspector and Contractor deem it to be a significant non-conforming item
Answer: D
NEW QUESTION # 34
Upon arrival of coating materials, the inspector should
- A. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- B. observe and document time frame and environmental conditions between each coat.
- C. observe and document the amount of material and batch numbers.
- D. observe aryl document that the applicator WFT at regular intervals during application.
Answer: C
NEW QUESTION # 35
A magnetic pull-off type gauge is a good choice when:
- A. Accuracy is not required
- B. When an intrinsically safe tool is required
- C. Performing an adhesion test
- D. When working on non-ferrous metals
Answer: B
NEW QUESTION # 36
Prior to using Inspection Tools the inspector must:
- A. Read the manufactures' instructions
- B. Ensure the instrument is within calibration parameters
- C. a), b) & c)
- D. Be trained on how to use the instrument
Answer: C
NEW QUESTION # 37
An Inspector should change position when:
- A. The Inspectors position is not the majority position
- B. Only when directed by the supervisor
- C. The Owner can save some money by the change
- D. The Inspector is convinced by verifiable facts
Answer: D
NEW QUESTION # 38
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Achieve consensus through negotiation
- B. Call the supervisor
- C. Go with the majority opinion
- D. Never change his/her mind
Answer: B
NEW QUESTION # 39
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 1
- B. Level 4
- C. Level 3
- D. Level 2
Answer: C
NEW QUESTION # 40
......
Ultimate Guide to the NACE-CIP1-001 - Latest Edition Available Now: https://www.ipassleader.com/NACE/NACE-CIP1-001-practice-exam-dumps.html
2025 Updated Verified Pass NACE-CIP1-001 Exam - Real Questions and Answers: https://drive.google.com/open?id=1XMqiqV4kxO1tKBTcy4dm46dXVEwO1B9S